IMO it is not important to cover each case with each sdnotify policy, to
speed them up we run all the exit code cases only once just twice for
each policy while switching the sdnotify policy between each case. This
way we safe 50% of runs and should still have sufficient coverage.
Before it took around 24 seconds, with this it is around 12 seconds now.
Signed-off-by: Paul Holzinger <pholzing@redhat.com>
There is really no point in waiting 10s for the kill, let's use 2 this
should be good enough to observe the timing.
Signed-off-by: Paul Holzinger <pholzing@redhat.com>
This test waits 15 seconds to send sigterm for no good reason, we can
just make the timeout shorter. Also make sure the podman command quit on
sigterm by looking for the output message.
While at it fix the tests to use $PODMAN_TMPDIR not /tmp and define the
yaml in the test instead of using the podman create && podman kube
generate && podman rm way to create the yaml as it is a bit slower as we
have to call three podman commands for it.
Signed-off-by: Paul Holzinger <pholzing@redhat.com>
Merge two podman event tests into one to speed them up as they did
mostly the same anyway. This way we only have to do the setup/teardown
once and only run one container.
Second, add the --since option because reading the journal can be slow
if you have thousands of event entries. This is not so critical in CI as
we run on fresh systems but on local dev machines I have almost 100k
events in the journal so parsing all of them makes this test slow (like
30s), with this change I can get it under 1s.
Signed-off-by: Paul Holzinger <pholzing@redhat.com>
Defining a timer with a fixed interval is not a good idea as we first
have to wait until the timer triggers, while the interval was every two
seconds it means that we have to wait at least 2s for it to start.
However much worse it means it triggers the unit over and over, this
seems to cause some soft of race with the output check. I have seen
this test run 10-60s which does not make much sense.
Switching the timer to trgger once on start seem to make the test run
consistently in 7s locally for me so this is much better.
There still is the question if we really have to test this at all on
each upstream PR but I left it for now.
Signed-off-by: Paul Holzinger <pholzing@redhat.com>
It takes over 10 seconds for this test as it uses --wait 5 twice which
runs into the timeout. IMO this tests is just redundant as it is already
covered in the e2e tests much better. Thus remove it here.
Signed-off-by: Paul Holzinger <pholzing@redhat.com>
Remove deactivated linters from the config as they will be removed in
the future and thorw warnings, all of them were disabled already anyway
so this is no functional change.
Second, fix one new lint warning for fmt.Scanln() error checking.
Signed-off-by: Paul Holzinger <pholzing@redhat.com>
It seems like podman kube play already supports the field since version 4.4.0 but the documentation was not yet updated.
Signed-off-by: thartd <49099022+pcguy85@users.noreply.github.com>
The new c/image version is returning a slightly new error message[1] so
make tests use the new one.
[1] https://github.com/containers/image/pull/2408
Signed-off-by: Paul Holzinger <pholzing@redhat.com>
Use the configuration parameters from the newly introduced
PodmanshConfig struct. This allows podmansh to be configured via
configuration files.
Signed-off-by: phoenix <felix.niederwanger@suse.com>
When an empty volume is mounted into a container, Docker will
chown that volume appropriately for use in the container. Podman
does this as well, but there are differences in the details. In
Podman, a chown is presently a one-and-done deal; in Docker, it
will continue so long as the volume remains empty. Mount into a
dozen containers, but never add content, the chown occurs every
time. The chown is also linked to copy-up; it will always occur
when a copy-up occurred, despite the volume now not being empty.
This PR changes our logic to (mostly) match Docker's.
For some reason, the chowning also stops if the volume is chowned
to root at any point. This feels like a Docker bug, but as they
say, bug for bug compatible.
In retrospect, using bools for NeedsChown and NeedsCopyUp was a
mistake. Docker isn't actually tracking this stuff; they're just
doing a copy-up and permissions change unconditionally as long as
the volume is empty. They also have the two linked as one
operation, seemingly, despite happening at very different times
during container init. Replicating that in our stateful system is
nontrivial, hence the need for the new CopiedUp field. Basically,
we never want to chown a volume with contents in it, except if
that data is a result of a copy-up that resulted from mounting
into the current container. Tracking who did the copy-up is the
easiest way to do this.
Fixes#22571
Signed-off-by: Matthew Heon <matthew.heon@pm.me>
If a container unit starts on boot with a dependency on `default.target`
the image unit may start too soon, before network is ready. This cause
the unit to fail to pull the image.
- Add a dependency on `network-online.target` to make sure image pulls
don't fail.
See https://github.com/containers/podman/issues/21873
- Document the hardcoded dependency on `network-online.target` for images unit
and explain how it can be overriden if necessary.
- tests/e2e/quadlet: Add `assert-last-key-regex`
Required to test the `After=` override in [Unit] section
See https://github.com/containers/podman/pull/22057#issuecomment-2008959993
- quadlet/unitfile: add a prepenUnitLine method
Requirements on networks should be inserted at the top of the
section so the user can override them.
Signed-off-by: jbtrystram <jbtrystram@redhat.com>
The default_addr shell function in test/system/helpers.network is used to
get the host's default address, which is used in a number of pasta
networking tests. However, in certain circumstances it can incorrectly
pick a deprecated address as the primary address. Correct it to exclude
those.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
* Document that pasta is now the default network driver
* Document command: podman info -f '{{.Host.RootlessNetworkCmd}}'
* Add note about missing network isolation
Fixes: https://github.com/containers/podman/issues/22748
Co-authored-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Erik Sjölund <erik.sjolund@gmail.com>
It's been flaking heavily since March. I don't see any new
development going on in minikube-land. If anyone decides
to care about minikube again, they can reenable this.
Signed-off-by: Ed Santiago <santiago@redhat.com>
In GetDefaultDevices(), make sure MachineConfig has an AppleHypervisor
instance before attempting to access it. This fixes a SIGSEGV when
running with libkrun as machine provider.
Signed-off-by: Sergio Lopez <slp@redhat.com>
Update the podman network docs to specify that the default rootless
networking tool has been swapped from slirp4netns to pasta.
Signed-off-by: Pranav RK <pranavrk7@gmail.com>
