mirror of
https://github.com/espressif/binutils-gdb.git
synced 2025-06-25 13:27:26 +08:00
2d97cd356e
Without this patch, when doing a software single step, with for example
a conditional breakpoint, gdbserver would wrongly avance the pc of
breakpoint_len and skips an instruction.
This is due to gdbserver assuming that it's hardware single stepping.
When it resumes from the breakpoint address it expects the trap to be
caused by ptrace and if it's rather caused by a software breakpoint
it assumes this is a permanent breakpoint and that it needs to skip
over it.
However when software single stepping, this breakpoint is legitimate as
it's the reinsert breakpoint gdbserver has put in place to break at
the next instruction. Thus gdbserver wrongly advances the pc and skips
an instruction.
This patch fixes this behavior so that gdbserver checks if it is a
reinsert breakpoint from software single stepping. If it is it won't
advance the pc. And if there's no reinsert breakpoint there we assume
then that it's a permanent breakpoint and advance the pc.
Here's a commented log of what would happen before and after the fix on
gdbserver :
/* Here there is a conditional breakpoint at 0x10428 that needs to be
stepped over. */
Need step over [LWP 11204]? yes, found breakpoint at 0x10428
...
/* e7f001f0 is a breakpoint instruction on arm
Here gdbserver writes the software breakpoint we would like to hit
*/
Writing e7f001f0 to 0x0001042c in process 11204
...
Resuming lwp 11220 (continue, signal 0, stop not expected)
pending reinsert at 0x10428
stop pc is 00010428
continue from pc 0x10428
...
/* Here gdbserver hit the software breakpoint that was in place
for the step over */
stop pc is 0001042c
pc is 0x1042c
step-over for LWP 11220.11220 executed software breakpoint
Finished step over.
Could not find fast tracepoint jump at 0x10428 in list (reinserting).
/* Here gdbserver writes back the original instruction */
Writing e50b3008 to 0x0001042c in process 11220
Step-over finished.
Need step over [LWP 11220]? No
/* Here because gdbserver assumes this is a permenant breakpoint it advances
the pc of breakpoint_len, in this case 4 bytes, so we have just skipped
the instruction that was written back here :
Writing e50b3008 to 0x0001042c in process 11220
*/
stop pc is 00010430
pc is 0x10430
Need step over [LWP 11220]? No, no breakpoint found at 0x10430
Proceeding, no step-over needed
proceed_one_lwp: lwp 11220
stop pc is 00010430
This patch fixes this situation and we get the right behavior :
Writing e50b3008 to 0x0001042c in process 11245
Hit a gdbserver breakpoint.
Hit a gdbserver breakpoint.
Step-over finished.
proceeding all threads.
Need step over [LWP 11245]? No
stop pc is 0001042c
pc is 0x1042c
Need step over [LWP 11245]? No, no breakpoint found at 0x1042c
Proceeding, no step-over needed
proceed_one_lwp: lwp 11245
stop pc is 0001042c
pc is 0x1042c
Resuming lwp 11245 (continue, signal 0, stop not expected)
stop pc is 0001042c
continue from pc 0x1042c
It also works if the value at 0x0001042c is a permanent breakpoint.
If so gdbserver will finish the step over, remove the reinserted breakpoint,
resume at that location and on the next SIGTRAP gdbserver will trigger
the advance PC condition as reinsert_breakpoint_inserted_here will be false.
I also tested this against bp-permanent.exp on arm (with a work in progress
software single step patchset) without any regressions.
It's also tested against x86 bp-permanent.exp without any regression.
So both software and hardware single step are tested.
No regressions on Ubuntu 14.04 on ARMv7 and x86.
With gdbserver-{native,extended} / { -marm -mthumb }
gdb/gdbserver/ChangeLog:
* linux-low.c (linux_wait_1): Fix pc advance condition.
* mem-break.c (reinsert_breakpoint_inserted_here): New function.
* mem-break.h (reinsert_breakpoint_inserted_here): New declaration.
README for GNU development tools This directory contains various GNU compilers, assemblers, linkers, debuggers, etc., plus their support routines, definitions, and documentation. If you are receiving this as part of a GDB release, see the file gdb/README. If with a binutils release, see binutils/README; if with a libg++ release, see libg++/README, etc. That'll give you info about this package -- supported targets, how to use it, how to report bugs, etc. It is now possible to automatically configure and build a variety of tools with one command. To build all of the tools contained herein, run the ``configure'' script here, e.g.: ./configure make To install them (by default in /usr/local/bin, /usr/local/lib, etc), then do: make install (If the configure script can't determine your type of computer, give it the name as an argument, for instance ``./configure sun4''. You can use the script ``config.sub'' to test whether a name is recognized; if it is, config.sub translates it to a triplet specifying CPU, vendor, and OS.) If you have more than one compiler on your system, it is often best to explicitly set CC in the environment before running configure, and to also set CC when running make. For example (assuming sh/bash/ksh): CC=gcc ./configure make A similar example using csh: setenv CC gcc ./configure make Much of the code and documentation enclosed is copyright by the Free Software Foundation, Inc. See the file COPYING or COPYING.LIB in the various directories, for a description of the GNU General Public License terms under which you can copy the files. REPORTING BUGS: Again, see gdb/README, binutils/README, etc., for info on where and how to report problems.