The size of the state-component bitmap as specified in
Intel(R) 64 and IA-32 Architectures Software Developer's Manual,
Chapter 13.4.2 is 8 bytes.
So far, the data types used for xstate_bv_p (gdb_byte*),
clear_bv (unsigned int) and tdep->xcr0 (uint64_t) were
inconsistent. But, since the xstate components were still
fitting into a single byte, the code still worked
as expected.
However, with the addition of the PKU feature (bit 9),
using one byte for the bitmap will no longer be sufficient.
This patch changes related code to use 64 bit data types
consistently and changes read/write acces of the XSAVE
header in the xsave buffer to use the endianess-aware
functions extract_unsigned_integer and store_unsigned_integer.
This is required to make sure that eventual differences
in endianess between host and target are taken care off.
gdb/Changelog:
2016-04-18 Michael Sturm <michael.sturm@intel.com>
* i387-tdep.c (i387_supply_xsave): Change type
of clear_bv to ULONGEST. Replace gdb_byte *xstate_bv_p
with ULONGEST xstate_bv and use extract_unsigned_integer
and store_unsigned_integer to read/write its value from
the xsave buffer.
(i387_collect_xsave): Replace gdb_byte *xstate_bv_p
with ULONGEST initial_xstate_bv and use
extract_unsigned_integer/store_unsigned_integer to
read/write its value from the xsave buffer.
Change type of clear_bv to ULONGEST.
gdbserver/Changelog:
2016-04-18 Michael Sturm <michael.sturm@intel.com>
* i387-fp.c (i387_cache_to_xsave): Change type of clear_bv to
unsigned long long.
(i387_fxsave_to_cache): Likewise.
Change-Id: I0de254158960b4f7bcbc9fe2fb857034fa1f7ca5
Signed-off-by: Michael Sturm <michael.sturm@intel.com>
Pedro suggested a separate patch synching with GCCs cpuid.h
instead of just adding new bits for PKU feature.
gdb/Changelog:
2016-11-14 Michael Sturm <michael.sturm@intel.com>
* nat/x86-gcc-cpuid.h: Replace with copy of cpuid.h
from gcc-6 branch.
Change-Id: I16f8f7f2d0aa7c2e815701d15ed831a6c6b33d21
Signed-off-by: Michael Sturm <michael.sturm@intel.com>
The direct references in objcopy kind of look like a hack to me, so
I'm calling these symbols internal too. Certainly they aren't named
and documented as a public BFD symbol today anyway.
So ... give these bfd-internal symbols with external linkage a _bfd_
prefix to avoid collisions in the global symbol namespace.
While at it, give them names that more closely match the corresponding
option name that toggles them.
Also while at it, fix a few related comment typos.
gdb/ChangeLog:
2017-02-17 Pedro Alves <palves@redhat.com>
* srec.c (Chunk): Rename to ...
(_bfd_srec_len): ... this.
(S3Forced): Rename to ...
(_bfd_srec_forceS3): ... this.
* objcopy.c: Adjust all references.
Give these bfd-internal symbols with external linkage a _bfd_ prefix
to avoid collisions in the global symbol namespace.
bfd/ChangeLog:
2017-02-17 Pedro Alves <palves@redhat.com>
* archive.c (bsd_write_armap): Rename to ...
(_bfd_bsd_write_armap): ... this.
(coff_write_armap): Rename to ...
(_bfd_coff_write_armap): ... this.
* libbfd-in.h (bsd_write_armap): Rename to ...
(_bfd_bsd_write_armap): ... this.
(coff_write_armap): Rename to ...
(_bfd_coff_write_armap): ... this.
* aout-target.h, aout-tic30.c: Adjust all users.
* libbfd.h: Regenerate.
Give this bfd-internal symbol with external linkage a _bfd_ prefix to
avoid collisions in the global symbol namespace.
bfd/ChangeLog:
2017-02-17 Pedro Alves <palves@redhat.com>
* bfd-in.h (bfd_read, bfd_write): Adjust to rename.
(warn_deprecated): Rename to ...
(_bfd_warn_deprecated): ... this.
* libbfd.c (warn_deprecated): Rename to ...
(_bfd_warn_deprecated): ... this.
* bfd-in2.h: Regenerate.
Give these bfd-internal symbols with external linkage a _bfd_ prefix
to avoid collisions in the global symbol namespace.
bfd/ChangeLog:
2017-02-17 Pedro Alves <palves@redhat.com>
* bfdio.c (real_ftell): Rename to ...
(_bfd_real_ftell): ... this.
(real_fseek): Rename to ...
(_bfd_real_fseek): ... this.
(real_fopen): Rename to ...
(_bfd_real_fopen): ... this.
* libbfd-in.h (real_ftell): Rename to ...
(_bfd_real_ftell): ... this.
(real_fseek): Rename to ...
(_bfd_real_fseek): ... this.
(real_fopen): Rename to ...
(_bfd_real_fopen): ... this.
* cache.c, dwarf2.c, opncls.c: Adjust all callers.
* libbfd.h: Regenerate.
Give these bfd-internal symbols with external linkage a _bfd_ prefix
to avoid collisions in the global symbol namespace.
bfd/ChangeLog:
2017-02-17 Pedro Alves <palves@redhat.com>
* dwarf2.c, elf-attrs.c, elf32-nds32.c: Adjust all callers.
* libbfd.c (read_unsigned_leb128): Rename to ...
(_bfd_read_unsigned_leb128): ... this.
(read_signed_leb128): Rename to ...
(_bfd_read_signed_leb128): ... this.
(safe_read_leb128): Rename to ...
(_bfd_safe_read_leb128): ... this.
* libbfd-in.h (read_unsigned_leb128): Rename to ...
(_bfd_read_unsigned_leb128): ... this.
(read_signed_leb128): Rename to ...
(_bfd_read_signed_leb128): ... this.
(safe_read_leb128): Rename to ...
(_bfd_safe_read_leb128): ... this.
* libbfd.h: Renegerate.
When looking up file and line information (used from the linker to
report error messages) if no symbol is passed in, then use the symbol
list to look for a matching symbol.
If a matching symbol is found then use this to look up the file / line
information.
This should improve errors when looking up file / line information for
data sections. Hopefully we should find a matching data symbol, which
should, in turn (we hope) match a DW_TAG_variable in the DWARF, this
should allow us to give accurate file / line errors for data symbols.
As the hope is to find a matching DW_TAG_variable in the DWARF then we
ignore section symbols, and prefer global symbols to locals.
bfd/ChangeLog:
* dwarf2.c (_bfd_dwarf2_find_nearest_line): Perform symbol lookup
before trying to fine matching file and line information.
ld/ChangeLog:
* testsuite/ld-elf/shared.exp: Update expected results.
* testsuite/ld-elf/dwarf2.err: Likewise
When parsing DWARF data in order to report file/line type error messages
we perform section placement to make section addresses unique within
relocatable object files.
Currently, if we reuse previously loaded (and cached) dwarf data then we
neglect to perform section placement, the result is that the section
addresses will not be unique, and we might, incorrectly associate an
address with the wrong debug information, and so report an incorrect
file and line number.
Further we neglect to check that that bfd for which we are looking up
debug information is actually the bfd for which the previous debug
information was loaded, it is possible that we will reuse previously
loaded debug information for a different bfd.
And finally, due to following of gnu_debuglink links in one bfd to
another, the process of checking that the cached debug information is
valid requires us to track the original bfd in the cached debug
information. The original debug information here is either the bfd that
we're interested in, not the bfd we finally load the debug information
from.
bfd/ChangeLog:
* dwarf2.c (struct dwarf2_debug): Add orig_bfd member.
(_bfd_dwarf2_slurp_debug_info): If stashed debug information does
not match current bfd, then reload debug information. Record bfd
we're loading debug info for in the stash. If we have debug
informatin in the cache then perform section placement before
returning.
ld/ChangeLog:
* testsuite/ld-elf/dwarf.exp (build_tests): Add new tests.
* testsuite/ld-elf/dwarf2.err: New file.
* testsuite/ld-elf/dwarf2a.c: New file.
* testsuite/ld-elf/dwarf2b.c: New file.
* testsuite/ld-elf/dwarf3.c: New file.
* testsuite/ld-elf/dwarf3.err: New file.
This commit adds new actions to the run_cc_link_tests mechanism in the
linker testsuite.
Previously this procedure could take a parameter containing a regular
expression that would be matched against warnings from the linker.
After this commit the warnings parameter is removed, instead, the
actions list can contain the actions 'warning', 'error',
'warning_output', or 'error_output'. The action names are chosen to
match the actions already present in the run_dump_test procedure.
These new actions allow for the current warning checking, but also allow
for checking of errors using a regular expression. More interestingly,
the *_output actions allow for the warning/error patterns to be placed
in a separate file.
The small number of tests that make use of the warning parameter have
been updated to the new mechanism. Later commits will make use of the
new features added in this commit.
ld/ChangeLog:
* testsuite/lib/ld-lib.exp (run_cc_link_tests): Add warning,
error, warning_output, and error_output actions. Remove separate
warnings parameter.
* testsuite/ld-elf/shared.exp (build_tests): Updated to use
'warning' action.
* testsuite/ld-plugin/lto.exp (lto_link_tests): Likewise.
ld/testsuite/ld-elf/check-ptr-eq.c fails for hppa, since function
pointers may point at plabels. It isn't valid to cast two function
pointers to void* and then compare the void pointers.
* testsuite/ld-elf/check-ptr-eq.c (check_ptr_eq): Change params
from void pointers to function pointers.
* testsuite/ld-elf/pr18718.c: Update to suit.
* testsuite/ld-elf/pr18720a.c: Update to suit.
I misunderstood the hppa alias problem. File offsets of segments need
to be such that no page is mapped twice with different permissions.
(Which still seems to me like something the kernel could fix, but
anyhow, this is not so difficult to achieve in ld.)
PR 21000
bfd/
* elf-bfd.h (struct elf_backend_data): Add no_page_alias.
* elfxx-target.h (elf_backend_no_page_alias): Define.
(elfNN_bed): Init new field.
* elf.c (assign_file_positions_for_load_sections): If no_page_alias
ensure PT_LOAD segment starts on a new page.
* elf32-hppa.c (elf_backend_no_page_alias): Define.
ld/
* testsuite/ld-elf/loadaddr1.d: Adjust for hppa file offsets.
* testsuite/ld-elf/loadaddr2.d: Likewise.
* testsuite/ld-elf/loadaddr3a.d: Likewise.
* testsuite/ld-scripts/rgn-at5.d: Likewise.
This fixes a long-standing hppa bug seen when generating PIEs, and I
think possible to trigger with forced local symbols in shared
libraries. Not allocating enough space for PLT relocs results in ld
writing outside of the buffer.
PR 21132
* elf32-hppa.c (allocate_plt_static): Allocate space for relocs
if pic.
This is a fix for PR gdb/21164. The problem started to happen after:
commit 34c41c681f4a0a0dfe0405c7d2aecf458520557a
Author: Doug Evans <xdje42@gmail.com>
AuthorDate: Mon Dec 19 08:33:46 2016 -0800
New syntax for mt print symbols,msymbols,psymbols.
This change introduced new syntax for the mentioned commands, and
improved the parsing of arguments by using 'gdb_buildargv'. However,
it is necessary to check if the argv being built is not NULL, which
can happen if the user doesn't provide any arguments to these
commands.
gdb/ChangeLog:
2017-02-15 Sergio Durigan Junior <sergiodj@redhat.com>
PR gdb/21164
* psymtab.c (maintenance_print_psymbols): Verify if 'argv' is not
NULL before using it.
* symmisc.c (maintenance_print_symbols): Likewise.
(maintenance_print_msymbols): Likewise.
gdb/testsuite/ChangeLog:
gdb/ChangeLog:
2017-02-15 Sergio Durigan Junior <sergiodj@redhat.com>
PR gdb/21164
* gdb.base/maint.exp: Add testcases for when the commands do
not have arguments.
"lea foo@GOT, %reg" is OK in PIC since it only loads the GOT offset
into register, which can be used later with a GOT base register to
get the value in the GOT entry.
bfd/
PR ld/21168
* elf32-i386.c (elf_i386_relocate_section): Allow
"lea foo@GOT, %reg" in PIC.
ld/
PR ld/21168
* testsuite/ld-i386/i386.exp: Run pr21168.
* testsuite/ld-i386/pr21168a.c: New file.
* testsuite/ld-i386/pr21168b.S: Likewise.
bfd/
PR ld/20244
* elf32-i386.c (elf_i386_relocate_section): Properly get IFUNC
symbol name when reporting R_386_GOT32/R_386_GOT32X relocation
error against local IFUNC symbol without a base register for
PIC.
ld/
PR ld/20244
* testsuite/ld-i386/i386.exp: Run pr20244-4a, pr20244-4b and
pr20244-4c.
* testsuite/ld-i386/pr20244-4.s: New file.
* testsuite/ld-i386/pr20244-4a.d: Likewise.
* testsuite/ld-i386/pr20244-4b.d: Likewise.
* testsuite/ld-i386/pr20244-4c.d: Likewise.
This patch adds the SVE-specific system registers.
opcodes/
* aarch64-opc.c (aarch64_sys_regs): Add SVE registers.
(aarch64_sys_reg_supported_p): Handle them.
gas/
* testsuite/gas/aarch64/sve-sysreg.s,
testsuite/gas/aarch64/sve-sysreg.d,
testsuite/gas/aarch64/sve-sysreg-invalid.d,
testsuite/gas/aarch64/sve-sysreg-invalid.l: New tests.
The documentation entry for the SVE feature incorrectly said that
it was enabled by default for ARMv8-A or later. This patch fixes
that and also mentions that +sve implies +simd. (It also implies
+fp, but that follows by transitivity.)
gas/
* doc/c-aarch64.texi: Fix sve entry.
Remove an inconsistency in linker error message processing causing that
it depends on the ability to infer the name of the originating source
file whether or not the name of the offending function is repeated by
clever formatters for each issue reported within the function.
Taking the `ld/testsuite/ld-powerpc/tocopt7.s' test case source as an
example and the `powerpc-linux' target we have:
$ as -gdwarf2 -o tocopt.o -a64 tocopt.s
$ ld -o tocopt -melf64ppc tocopt.o
tocopt.o: In function `_start':
tocopt.s:35:(.text+0x14): toc optimization is not supported for 0x3fa00000 instruction.
tocopt.s:49:(.text+0x34): toc optimization is not supported for 0x3fa00000 instruction.
$
vs:
$ as -o tocopt.o -a64 tocopt.s
$ ld -o tocopt -melf64ppc tocopt.o
tocopt.o: In function `_start':
(.text+0x14): toc optimization is not supported for 0x3fa00000 instruction.
tocopt.o: In function `_start':
(.text+0x34): toc optimization is not supported for 0x3fa00000 instruction.
$
Similarly with the `mips-linux' target and this source:
$ cat jal-global-multi-overflow.s
.text
.set noreorder
.space 0x2000
.align 4
.globl foo
.ent foo
foo:
jal bar
nor $0, $0
jal bar
nor $0, $0
.end foo
.space 0x1ff0
.align 4
.globl bar
.ent bar
bar:
jal foo
nor $0, $0
jal foo
nor $0, $0
.end bar
$ as -o jal-global-multi-overflow.o jal-global-multi-overflow.s
$ ld -Ttext 0x1fffd000 -e foo -o jal-global-multi-overflow jal-global-multi-overflow.o
jal-global-multi-overflow.o: In function `foo':
(.text+0x2000): relocation truncated to fit: R_MIPS_26 against `bar'
jal-global-multi-overflow.o: In function `foo':
(.text+0x2008): relocation truncated to fit: R_MIPS_26 against `bar'
jal-global-multi-overflow.o: In function `bar':
(.text+0x4000): relocation truncated to fit: R_MIPS_26 against `foo'
jal-global-multi-overflow.o: In function `bar':
(.text+0x4008): relocation truncated to fit: R_MIPS_26 against `foo'
$
Not only this is inconsistent, but it causes output clutter as well with
redundant information.
The cause for this is a check in `vfinfo' the intent of which is to
print the function heading whenever (among others) the name of the
source file has changed, which however does not take into account a
situation where the name couldn't have been established both now and
previously.
Adjust the check then for this situation, yielding:
$ as -o tocopt.o -a64 tocopt.s
$ ld -o tocopt -melf64ppc tocopt.o
tocopt.o: In function `_start':
(.text+0x14): toc optimization is not supported for 0x3fa00000 instruction.
(.text+0x34): toc optimization is not supported for 0x3fa00000 instruction.
$
and:
$ as -o jal-global-multi-overflow.o jal-global-multi-overflow.s
$ ld -Ttext 0x1fffd000 -e foo -o jal-global-multi-overflow jal-global-multi-overflow.o
jal-global-multi-overflow.o: In function `foo':
(.text+0x2000): relocation truncated to fit: R_MIPS_26 against `bar'
(.text+0x2008): relocation truncated to fit: R_MIPS_26 against `bar'
jal-global-multi-overflow.o: In function `bar':
(.text+0x4000): relocation truncated to fit: R_MIPS_26 against `foo'
(.text+0x4008): relocation truncated to fit: R_MIPS_26 against `foo'
$
respectively instead. Adjust the test suite accordingly.
ld/
* ldmisc.c (vfinfo): Don't print the function name again either
if no source file name has been found both now and previously.
* testsuite/ld-cris/tls-err-20x.d: Adjust accordingly.
* testsuite/ld-mips-elf/mode-change-error-1.d: Likewise.
* testsuite/ld-mips-elf/unaligned-branch.d: Likewise.
* testsuite/ld-mips-elf/unaligned-branch-mips16.d: Likewise.
* testsuite/ld-mips-elf/unaligned-branch-micromips.d: Likewise.
* testsuite/ld-mips-elf/unaligned-branch-r6-1.d: Likewise.
* testsuite/ld-mips-elf/unaligned-branch-2.d: Likewise.
* testsuite/ld-mips-elf/unaligned-branch-r6-2.d: Likewise.
* testsuite/ld-mips-elf/unaligned-branch-ignore-2.d: Likewise.
* testsuite/ld-mips-elf/unaligned-branch-ignore-mips16.d:
Likewise.
* testsuite/ld-mips-elf/unaligned-branch-ignore-micromips.d:
Likewise.
* testsuite/ld-mips-elf/unaligned-branch-ignore-r6-1.d:
Likewise.
* testsuite/ld-mips-elf/unaligned-jalx-addend-1.d: Likewise.
* testsuite/ld-mips-elf/unaligned-jalx-addend-mips16-1.d:
Likewise.
* testsuite/ld-mips-elf/unaligned-jalx-addend-micromips-1.d:
Likewise.
* testsuite/ld-mips-elf/unaligned-jalx-addend-3.d: Likewise.
* testsuite/ld-mips-elf/unaligned-jump.d: Likewise.
* testsuite/ld-mips-elf/unaligned-jump-mips16.d: Likewise.
* testsuite/ld-mips-elf/unaligned-jump-micromips.d: Likewise.
* testsuite/ld-mips-elf/unaligned-lwpc-1.d: Likewise.
* testsuite/ld-mips-elf/unaligned-ldpc-1.d: Likewise.
* testsuite/ld-powerpc/tocopt.out: Likewise.
* testsuite/ld-powerpc/tocopt7.out: Likewise.
Remove an inconsistency in BFD linker error messages across the PowerPC
backends, where in the presence of line information the `%P: %H:' format
sequence makes the first error message produced for any given function
different from subsequent ones.
Taking the `ld/testsuite/ld-powerpc/tocopt7.s' test case source as an
example and the `powerpc-linux' target we have:
$ as -gdwarf2 -o tocopt.o -a64 tocopt.s
$ ld -o tocopt -melf64ppc tocopt.o
ld: tocopt.o: In function `_start':
tocopt.s:35:(.text+0x14): toc optimization is not supported for 0x3fa00000 instruction.
ld: tocopt.s:49:(.text+0x34): toc optimization is not supported for 0x3fa00000 instruction.
$
where the first error message does not have the source file name
prefixed with the linker program executable's name, i.e. `ld:', whereas
the second error message does, as would any subsequent.
This is because with a multiple-line error message such as `%H' produces
`%P' only prints the program executable's name on the first line and not
any later ones. Also the PowerPC backend is the only part of BFD which
uses `%P' along with one of the clever `%C', `%D', `%G', `%H' format
specifiers. And last but not least this breaks a GNU Coding Standard's
requirement that error messages from compilers should look like this:
source-file-name:lineno: message
also quoted in `vfinfo' code handling these specifiers.
Convert `%P: %H:' to `%H:' in error messages across the PowerPC backends
then, yielding:
$ as -gdwarf2 -o tocopt.o -a64 tocopt.s
$ ld -o tocopt -melf64ppc tocopt.o
tocopt.o: In function `_start':
tocopt.s:35:(.text+0x14): toc optimization is not supported for 0x3fa00000 instruction.
tocopt.s:49:(.text+0x34): toc optimization is not supported for 0x3fa00000 instruction.
$
instead, making it consistent and matching the GNU Coding Standard's
requirement.
bfd/
* elf32-ppc.c (ppc_elf_check_relocs): Use `%H:' rather than
`%P: %H:' with `info->callbacks->einfo'.
(ppc_elf_relocate_section): Likewise.
* elf64-ppc.c (ppc64_elf_check_relocs): Likewise.
(ppc64_elf_edit_toc): Likewise.
(ppc64_elf_relocate_section): Likewise.
Remove static NULL initializers, moving the respective variables from
data to BSS and saving some storage space.
ld/
* ldmisc.c (vfinfo) <'H'>: Remove static NULL initializers.
3d7b173c29900879c9a5958dd6029fd36666e57c made upper case commands now
illegal. However gdb.cp/chained-calls.exp still contains one test using
P to print an expression. This patch fixes the testcase to use p
instead.
2017-02-13 Thomas Preud'homme <thomas.preudhomme@arm.com>
gdb/
* gdb.cp/chained-calls.exp: Use p instead of P.
2017-02-15 Vladimir Radosavljevic <Vladimir.Radosavljevic@imgtec.com>
PR gold/21111
* mips.cc (Mips_relocate_functions::relhigher): New method.
(Mips_relocate_functions::relhighest): Likewise.
(mips_get_size_for_reloc): Add support for relocs: R_MIPS_HIGHER and
R_MIPS_HIGHEST.
(Target_mips::Scan::local): Add support for relocs: R_MIPS_HIGHER,
R_MIPS_HIGHEST, R_MICROMIPS_HIGHER and R_MICROMIPS_HIGHEST.
(Target_mips::Scan::global): Likewise.
(Target_mips::Scan::get_reference_flags): Likewise.
(Target_mips::Relocate::relocate): Call static methods for resolving
HIGHER and HIGHEST relocations.
opcodes * arc-regs.h: Distinguish some of the registers different on
ARC700 and HS38 cpus.
gas * testsuite/gas/arc/st.d: Update for 0xe having a name now
gold/
* x86_64.cc (Target_x86_64::do_can_check_for_function_pointers):
Return true even when building pie binaries.
(Target_x86_64::possible_function_pointer_reloc): Check opcode
for R_X86_64_PC32 relocations.
(Target_x86_64::local_reloc_may_be_function_pointer): Pass
extra arguments to local_reloc_may_be_function_pointer.
(Target_x86_64::global_reloc_may_be_function_pointer): Likewise.
* gc.h (gc_process_relocs): Add check for STT_FUNC.
* testsuite/Makefile.am (icf_safe_pie_test): New test case.
* testsuite/Makefile.in: Regenerate.
* testsuite/icf_safe_pie_test.sh: New shell script.
sim/aarch64/
* simulator.c (do_vec_bit): Change loop limits from 16 and 8 to 4 and
2. Move test_false if inside loop. Fix logic for computing result
stored to vd.
sim/testsuite/sim/aarch64
* bit.s: New.
sim/aarch64/
* simulator.c: (LDn_STn_SINGLE_LANE_AND_SIZE): New.
(do_vec_LDn_single, do_vec_STn_single): New.
(do_vec_LDnR): Add and set new nregs var. Replace switch on nregs with
loop over nregs using new var n. Add n times size to address in loop.
Add n to vd in loop.
(do_vec_load_store): Add comment for instruction bit 24. New var
single to hold instruction bit 24. Add new code to use single. Move
ldnr support inside single if statements. Fix ldnr register counts
inside post if statement. Change HALT_NYI calls to HALT_UNALLOC.
sim/testsuite/sim/aarch64/
* ldn_single.s: New.
* ldnr.s: New.
* stn_single.s: New.
This adds an event that is emitted just before GDB presents a prompt
to the user. This provides Python code a way to react to whatever
changes might have been made by the previous command. For example, in
my GUI I use this to track changes to the selected frame and reflect
them in the UI.
Built and regtested on x86-64 Fedora 23.
gdb/ChangeLog
2017-02-14 Tom Tromey <tom@tromey.com>
PR python/13598:
* python/python.c (gdbpy_before_prompt_hook): Emit before_prompt
event.
* python/py-evts.c (gdbpy_initialize_py_events): Add
before_prompt registry.
* python/py-events.h (events_object) <before_prompt>: New field.
gdb/doc/ChangeLog
2017-02-14 Tom Tromey <tom@tromey.com>
PR python/13598:
* python.texi (Events In Python): Document events.before_prompt.
gdb/testsuite/ChangeLog
2017-02-14 Tom Tromey <tom@tromey.com>
PR python/13598:
* gdb.python/py-events.exp: Add before_prompt event tests.
The test case implptrpiece.exp accesses the second byte of the short
integer number 1 and expects it to be zero. This is valid for
little-endian targets, but fails on big-endian targets.
This is fixed by distinguishing the expected value by endianness.
gdb/testsuite/ChangeLog:
* gdb.dwarf2/implptrpiece.exp: Fix check for big-endian targets.
