Make comp_unit_head.length private, to enforce using accessor functions.
Replace accessor function get_length with get_length_with_initial and
get_length_without_initial, to make it explicit which variant we're using.
Tested on x86_64-linux.
PR symtab/29343
Bug: https://sourceware.org/bugzilla/show_bug.cgi?id=29343
This fixes a couple of places in display_debug_lines_decoded that were
off by one in checking DWARF5 .debug_line directory indices. It also
displays the DWARF5 entry 0 for the program current directory rather
than "." as is done for pre-DWARF5. I decided against displaying
DW_AT_comp_dir for pre-DWARF5 since I figure it is better for readelf
to minimally interpret debug info.
binutils/
PR 29948
* dwarf.c (display_debug_lines_decoded): Display the given
directory entry 0 for DWARF5. Properly check directory index
against number of entries in the table. Revert to using
unsigned int for n_directories and associated variables.
Correct warning messages.
gas/
* testsuite/gas/elf/dwarf-5-loc0.d: Update.
This commit makes CSR class handling for 'Smstateen' and 'Ssstateen'
extensions simpler using fall-throughs (as used in CSR_CLASS_I{,_32}).
gas/ChangeLog:
* config/tc-riscv.c (riscv_csr_address): Simplify the logic for
'Smstateen' and 'Ssstateen' extensions.
PR cli/29945 points out that "set debug timestamp 1" stopped working
-- this is a regression due to commit b8043d27 ("Remove a ui-related
memory leak").
This patch fixes the bug and adds a regression test.
I think this should probably be backported to the gdb 13 branch.
Bug: https://sourceware.org/bugzilla/show_bug.cgi?id=29945
When --no-keep-memory is used, the input section memory may not be cached.
Allocate input section memory for -z pack-relative-relocs if needed.
bfd/
PR ld/29939
* elfxx-x86.c (elf_x86_size_or_finish_relative_reloc): Allocate
input section memory if needed.
ld/
PR ld/29939
* testsuite/ld-elf/dt-relr-2i.d: New test.
A recent change in the XTheadFmv spec fixed an encoding bug in the
document. This patch changes the code to follow this bugfix.
Spec patch can be found here:
https://github.com/T-head-Semi/thead-extension-spec/pull/11
Signed-off-by: Christoph Müllner <christoph.muellner@vrull.eu>
The gdb.gdb self-tests were timing out for me, which turned out to be
PR testsuite/29325. Looking into it, the problem is that the version
of the Boehm GC that is used by Guile on my machine causes a SEGV
during stack probing. This unexpected stop confuses the tests and
causes repeated timeouts.
This patch adapts the two failing tests. This makes them work for me,
and reduces the running time of gdb.gdb from 20 minutes to about 11
seconds.
Bug: https://sourceware.org/bugzilla/show_bug.cgi?id=29325
The naming in here has grown organically and is confusing to follow.
Originally there was only one set of rules for generating code from
the igen sources, so calling it "tmp-igen" and such made sense. But
when other multigen modes were added ("m16" & "multi") which also
used igen, it's not clear what's common igen and what's specific to
this generation mode. So rename the set of rules from "igen" to
"single" so it's easier to follow.
The m16 & multi targets generate itable once even when all the other
modules are generated multiple times. The default igen target will
generate itable with everything else out of convenience. This means
flags are passed which don't affect the generated itable there.
We can unify the itable generation by making sure the right -F/-M
filter variables are passed down. Since there's already a dedicated
rule & variable in the multi build mode, generalize that and switch
the m16 & igen builds over too.
I spent a lot of time staring at this code, building for diff mips
targets, and exploring all the shell code paths. I think this is
safe, but only time (and users) will really tell.
This variable is only used to generate the itable files. In preparation
for merging the itable logic among all ports, rename "multi_flags" to a
more appropriate "igen_itable_flags" variable. There should be no real
chagnes here otherwise.
This code appears to be unused since it was first merged. When
micromips was enabled, it was via the "MULTI" config, not the
"MICROMIPS" config, and the multi configs have sep vars. Since
nothing sets SIM_MIPS_GEN=MICROMIPS in the config, all of this
should be unreachable, so punt it to simplify. Further, the
SIM_MIPS_MICROMIPS16_FLAGS & SIM_MIPS_MICROMIPS_FLAGS settings
rely on sim_mips_micromips{,16}_{filter,machine} variables that
are never set in the configure script.
PR symtab/29343 points out that it would be beneficial if
comp_unit_head had a constructor and used initializers. This patch
implements this. I'm unsure if this is sufficient to close the bug,
but at least it's a step.
Bug: https://sourceware.org/bugzilla/show_bug.cgi?id=29343
I think the test for table->files[file].dir being non-zero is wrong
for DWARF5 where index zero is allowed and is the current directory of
the compilation. Most times this will be covered by the use of
table->comp_dir (from DW_AT_comp_dir) in concat_filename but the point
of putting the current dir in .debug_line was so the section could
stand alone without .debug_info.
Also, there is no need to check for table->dirs non-NULL, the
table->num_dirs test is sufficient.
* dwarf2.c (concat_filename): Correct and simplify tests of
directory index.
The following test was failing on ppc64 and s390x:
"FAIL: encode-1: Encode buffer match"
The offending stub was how we memcpy the FRE start address to the buffer
(on-disk format). When the host is big-endian, the address of the
source buffer for the memcpy needs to point to the uint8_t/uint16_t sized
value of the FRE start addr, not uint32_t sized value; we intend to copy
out only the fre_start_addr_sz number of bytes.
ChangeLog:
* libsframe/sframe.c (sframe_encoder_write_fre_start_addr): New
function.
(sframe_encoder_write_fre): Use it instead of memcpy.
While mips has respected sim_igen_smp at configure time (which was
always empty since it defaulted smp to off), no other igen port did.
Move this to a makefile variable and plumb it through the common
IGEN_RUN variable instead so everyone gets it by default. We also
clean up some redundant -N0 setting with multirun mips.
All the runtimes were only initializing a single CPU. When SMP is
enabled, things quickly crash as none of the other CPU structs are
setup. Change the default from 0 to the compile time value.
The igen tool sets up the SD & CPU defines for code fragments to use,
but v850 was expecting "sd". Change all the igen related code to use
SD so it actually compiles, and fix a few places to use "CPU" instead
of hardcoding cpu0.
The igen tool sets up the SD define for code fragments to use, but
mn10300 was expecting "sd". Change all the igen related code to use
SD so it actually compiles.
This code fails to compile when SMP is enabled due to some obvious
errors. Fix those and change the logic to avoid CPP to prevent any
future rot from creeping back in.
This is the last bit of logic that exists in the mips configure
script, so move it to the top-level configure to kill it off.
We still have to move the Makefile.in igen logic to local.mk,
but this is a required first step for that.
To prepare moving this logic to the top-level configure, the vars
need to be namespaced. Do that here to make it easier to review.
Basically sim_xxx -> SIM_MIPS_XXX when a var is exported from the
configure script to the Makefile, and sim_xxx -> sim_mips_xxx when
the var is internal in the configure script.
Make sure the igen tool exists before trying to compile the mips
subdir. This happens to work when mips has a subconfigure, but
hits a race condition when that is removed.
Every file that igen outputs is then processed with the move-if-changed
shell script. This creates a lot of boilerplate in the build and not an
insignificant amount of build-time overhead. Move the simple "is the file
changed" logic into igen itself.
In commit:
commit 9f50fe0835850645bd8ea9bb1efe1fe6c48dfb12
Date: Wed Dec 7 15:55:25 2022 +0000
gdb/testsuite: new test for recent dwarf reader issue
A new test (gdb.base/signed-builtin-types.exp) was added that made use
of 'info sources' to figure out if the debug information for a
particular object file had been fully expanded or not. Unfortunately
some lines of the 'info sources' output can be very long, this was
observed on some systems where the debug information for the
dynamic-linker was installed, in this case, the list of source files
associated with the dynamic linker was so long it would cause expect's
internal buffer to overflow.
This commit switches from using 'info sources' to 'maint print
objfile', the output from the latter command is more compact, but
also, can be restricted to a single named object file.
With this change in place I am no longer seeing buffer overflow errors
from expect when running gdb.base/signed-builtin-types.exp.
There's no need for these settings to be in sim-main.h which is shared
with common/ sim code, so move it all out to the existing or1k-sim.h.
Unfortunately, we can't yet drop the or1k-sim.h include from sim-main.h
as many of the generated CGEN files refer only to sim-main.h. We'll
have to improve the CGEN interface before we can make more progress,
but this is at least a minor improvement.
