This won't have any useful effect, so is at best marginally less bogus
than a negative value.
The change actually points out a flawed (for Arm) testcase: @ is a
comment character there.
The noxfail option is useful in situations like pr23658-1e which
fails on all microblaze ELF targets except microblaze-linux. This was
possible to handle by writing a small proc and use that as an xfail
predicate, or painstakingly listing all microblaze ELF targets, but
this is simpler. The patch also fixes some other FAILs and XPASSes of
the pr23658 tests.
binutils/
* testsuite/lib/binutils-common.exp (run_dump_test): Support
noxfail.
ld/
* testsuite/ld-elf/pr23658-1a.d: Don't xfail m68hc12.
* testsuite/ld-elf/pr23658-1e.d: Likewise. xfail xstormy16
and correct microblaze xfails.
While for executables properly aligning sections within the file can be
quite relevant, the same is of pretty little importance for relocatable
object files. Avoid passing "true" into
_bfd_elf_assign_file_position_for_section() when dealing with object
files, but compensate minimally by applying log_file_align in such
cases as a cap to the alignment put in place.
This also makes the dlltool tests run more PE targets, finding that
sh-pe dlltool reports "Machine 'sh' not supported". I guess no one
cares about that.
PR19459
* dlltool.c (asm_prefix): Remove "mach" parameter. Return
leading_underscore independent of machine.
(ASM_PREFIX): Adjust.
* testsuite/binutils-all/dlltool.exp: Run on any target
satisfying is_pecoff_format for which dlltool is built.
Revert commit 0398b8d6c8. Remove target_xfail.
Previous code included the full $srcdir pathnames in the individual
subtest PASS/FAIL names, which makes it difficult to compute
comparisons or regressions between test runs on different machines.
This version switches to the basename only, which are common.
Signed-off-by: Frank Ch. Eigler <fche@redhat.com>
Add the MT ASE instruction operand types and encodings to the microMIPS
opcode table and enable the assembly of these instructions in GAS from
MIPSr2 onwards. Update the binutils and GAS testsuites accordingly.
References:
"MIPS Architecture for Programmers, Volume IV-f: The MIPS MT Module for
the microMIPS32 Architecture", MIPS Technologies, Inc., Document Number:
MD00768, Revision 1.12, July 16, 2013
Co-Authored-By: Maciej W. Rozycki <macro@redhat.com>
The new test wasn't being run, and failed due to relocations against
.gnu.build.attributes being stripped by default strip behaviour.
We probably should be keeping these relocations, but I haven't made
that change here.
BTW, the new test fails on ia64-hpux but that's just a repeat of the
existing note-5 fail.
PR 31999
* testsuite/binutils-all/strip-16.d: strip with --strip-unneeded
and --merge-notes.
* testsuite/binutils-all/objcopy.exp: Run the new test. Sort
other strip tests.
A number of instructions in the regular MIPS opcode table are assembly
idioms for the MT thread context move MFTR and MTTR instructions, so
mark them as aliases accordingly. Add suitable test cases, which also
cover the PAUSE assembly idiom.
This patch started life as a relatively simple change to fix some
unimportant objcopy memory leaks, but expanded into a larger patch
when I was annoyed by the awkwardness of passing data when using
bfd_map_over_sections. A simple loop over sections is much more
convenient, and we really don't need the abstraction layer. Sections
in a list isn't going to disappear any time soon.
The patch also removes use of the global "status" variable by all but
the top-level functions called from main.
* objcopy.c (filter_symbols): Return success as a bool. Pass
symcount as a pointer, updated on return.
(merge_gnu_build_notes): Similarly return a bool and add newsize
param with updated smaller section size.
(setup_bfd_headers): Return bool success rather than setting
"status" on failure.
(setup_section): Likewise.
(copy_relocations_in_section, copy_section): Likewise, and adjust
params.
(mark_symbols_used_in_relocations): Likewise, and free memory
on failure path. Don't call bfd_fatal.
(get_sections): Delete function.
(copy_object): Don't use bfd_map_over_sections, instead use a
loop allowing easy detection of failure status. Free memory on
error paths.
(copy_archive): Return bool success rather than setting "status"
on failure.
(copy_file): Set "status" here.
* testsuite/binutils-all/strip-13.d: Adjust to suit.
The logic is same as a71d876801 ("aarch64: Add DT_RELR support").
As LoongArch does not have -z dynamic-undefined-weak, we don't need to
consider UNDEFWEAK_NO_DYNAMIC_RELOC.
The linker relaxation adds another layer of complexity. When we delete
bytes in a section during relaxation, we need to fix up the offset in
the to-be-packed relative relocations against this section.
Signed-off-by: Xi Ruoyao <xry111@xry111.site>
Previously objcopy had to be run twice in order to make a local symbol
weak, first once to globalize it, and once again to mark it as weak.
* objcopy.c (filter_symbols): Weaken symbols after making
local/global changes.
* testsuite/binutils-all/symbols-5.d,
* testsuite/binutils-all/symbols-5.s: New test.
We should set BFD_DECOMPRESS to decompress sections unless dumping the
section contents when reading build-id debuglink.
PR binutils/31925
* objdump.c (open_debug_file): Set BFD_DECOMPRESS to decompress
sections unless dumping the section contents.
* testsuite/binutils-all/objdump.exp (test_build_id_debuglink):
Add a compress option.
Run test_build_id_debuglink with none and zlib.
Signed-off-by: H.J. Lu <hjl.tools@gmail.com>
Files named *.0 are somewhat odd for testsuite expectations. Rename the
one such file to *.r with a suitable base name suffix, and have its
sibling follow suit in this latter regard.
Implement a helper to construct a relative path between two locations in
the filesystem, for example to make a path from the source to the object
directory for the case where a tool has been set up to look at a given
path and there is a need to point it elsewhere, but an absolute path
will not work. The helper works on normalized paths internally, so the
result is correct even in the presence of symlinks as intermediate path
components.
So given "/path/to/src/gas/testsuite/gas/all" as the FROM argument and
then "/path/to/obj/gas/testsuite/tmpdir/none.s" as the TO argument the
helper will return "../../../../../obj/gas/testsuite/tmpdir/none.s" in
the absence of symlinks.
When printing a DW_MACRO_define_strx entry in a .debug_macro.dwo section, we
run into:
...
DW_MACRO_define_strx lineno : 0 macro : <no .debug_str_offsets section>
...
Fix this in display_debug_macro by passing the correct dwo argument to a
fetch_indexed_string call.
That works fine for readelf -w, with with readelf -wm we have:
...
DW_MACRO_define_strx lineno : 0 macro : <no .debug_str_offsets.dwo section>
...
Fix this in display_debug_macro by doing load_debug_section_with_follow for
str_dwo / str_index_dwo sections instead of str / str_index sections when
handling .debug_macro.dwo.
PR 31735
When compiling a hello world with dwarf4 split dwarf:
...
$ gcc -gdwarf-4 -gsplit-dwarf hello.c -save-temps -dA
...
we have in a-hello.s these three initial entries in .debug_str_offsets:
...
.section .debug_str_offsets.dwo,"e",@progbits
.4byte 0 // indexed string 0x0: short int
.4byte 0xa // indexed string 0x1: /home/vries/binutils
.4byte 0x1f // indexed string 0x2: main
...
but "readelf -ws a.out" starts at the third entry:
...
Contents of the .debug_str_offsets.dwo section (loaded from a-hello.dwo):
Length: 0x30
Index Offset [String]
0 00000000 main
...
This is a regression since commit 407115429b ("Modified changes for
split-dwarf and dwarf-5."), which introduced a variable
debug_str_offsets_hdr_len in display_debug_str_offsets.
Fix this by setting display_debug_str_offsets to 0 for the dwarf4 case.
PR 31734
Given that the disassembler should never abort when decoding
(potentially random) data, assertion statements in the
`get_*reg_qualifier_from_value' function family prove problematic.
Consider the random 32-bit word W, encoded in a data segment and
encountered on execution of `objdump -D <obj_name>'.
If:
(W & ~opcode_mask) == valid instruction
Then before `print_insn_aarch64_word' has a chance to report the
instruction as potentially undefined, an attempt will be made to have
the qualifiers for the instruction's register operands (if any)
decoded. If the relevant bits do not map onto a valid qualifier for
the matched instruction-like word, an abort will be triggered and the
execution of objdump aborted.
As this scenario is perfectly feasible and, in light of the fact that
objdump must successfully decode all sections of a given object file,
it is not appropriate to assert in this family of functions.
Therefore, we add a new pseudo-qualifier `AARCH64_OPND_QLF_ERR' for
handling invalid qualifier-associated values and re-purpose the
assertion conditions in qualifier-retrieving functions to be the
predicate guarding the returning of the calculated qualifier type.
If the predicate fails, we return this new qualifier and allow the
caller to handle the error as appropriate.
As these functions are called either from within
`aarch64_extract_operand' or `do_special_decoding', both of which are
expected to return non-zero values, it suffices that callers return
zero upon encountering `AARCH64_OPND_QLF_ERR'.
Ar present the error presented in the hypothetical scenario has been
encountered in `get_sreg_qualifier_from_value', but the change is made
to the whole family to keep the interface consistent.
Bug: https://sourceware.org/PR31595
Since ar can be built defaulting to deterministic mode, tests which
expect non-deterministic behaviour need to explicitly set the U flag.
The non-deterministic member test expects SOURCE_DATE_EPOCH to not be
set; this documents that. Unconditionally unsetting the variable
causes issues in test infrastructure (which expects unsetenv to only
be called on variables which are already set).
Signed-off-by: Stephen Kitt <steve@sk2.org>
PR ld/31289 tests failed for fr30-elf, frv-elf, ft32-elf, iq2000-elf,
mn10200-elf, ms1-elf and msp430-elf targets:
FAIL: ld-elf/fatal-warnings-2a
FAIL: ld-elf/fatal-warnings-2b
FAIL: ld-elf/fatal-warnings-3a
FAIL: ld-elf/fatal-warnings-3b
FAIL: ld-elf/fatal-warnings-4a
FAIL: ld-elf/fatal-warnings-4b
even though PR ld/31289 targets xfail for [is_generic] targets. These
targets not only don't use the generic_link_hash_table linker, but also
don't use the standard ELF emulation. Add is_standard_elf for ELF
targets which use the standard ELF emulation and replace [is_generic]
with ![is_standard_elf] in PR ld/31289 tests.
binutils/
PR ld/31289
* testsuite/lib/binutils-common.exp (is_standard_elf): New.
ld/
PR ld/31289
* testsuite/lib/binutils-common.exp (is_generic): Return 1 for
fr30-*-*, frv-*-elf, ft32-*-*, iq2000-*-*, mn10200-*-*,
moxie-*-moxiebox*, msp430-*-* and mt-*-*.
* testsuite/ld-elf/fatal-warnings-2a.d: Replace [is_generic]
with ![is_standard_elf].
* testsuite/ld-elf/fatal-warnings-2b.d: Likewise.
* testsuite/ld-elf/fatal-warnings-3a.d: Likewise.
* testsuite/ld-elf/fatal-warnings-3b.d: Likewise.
* testsuite/ld-elf/fatal-warnings-4a.d: Likewise.
* testsuite/ld-elf/fatal-warnings-4b.d: Likewise.
Adds two new external authors to etc/update-copyright.py to cover
bfd/ax_tls.m4, and adds gprofng to dirs handled automatically, then
updates copyright messages as follows:
1) Update cgen/utils.scm emitted copyrights.
2) Run "etc/update-copyright.py --this-year" with an extra external
author I haven't committed, 'Kalray SA.', to cover gas testsuite
files (which should have their copyright message removed).
3) Build with --enable-maintainer-mode --enable-cgen-maint=yes.
4) Check out */po/*.pot which we don't update frequently.
PR 31062
* objdump.c (decompressed_dumps): New local variable. (usage): Mention the -z/--decompress option. (long_options): Add --decompress. (dump_section_header): Add "COMPRESSED" to the Flags field of any compressed section. (dump_section): Warn users when dumping a compressed section. (display_any_bfd): Decompress the section if decompressed_dumps is true. (main): Handle the -z/--decompress option.
* NEWS: Mention the new feature.
* doc/binutils.texi: Document the new feature.
* testsuite/binutils-all/objdump.s: Update expected output.
* testsuite/binutils-all/objdump.exp: Add test of -Z -s.
* testsuite/binutils-all/objdump.Zs: New file.
* readelf.c (maybe_expand_or_relocate_section): New function. Contains common code found in dump functions. Adds a note message if a compressed section is not being decompressed. (dump_section_as_strings): Use new function. (dump_section_as_bytes): Likewise.
Add a 64-bit traditional MIPS dump variant for the `readelf -S bintest'
test from binutils-all/readelf.exp, using a filename suffix according to
the rules set there, removing:
FAIL: readelf -S bintest
regressions with `mips64-linux-gnuabi64', `mips64el-linux-gnuabi64',
`mips64-openbsd', and `mips64el-openbsd' targets, which default to the
n64 ABI and consequently produce a section layout that is different from
what the generic dump pattern covers.
Co-Authored-By: Maciej W. Rozycki <macro@orcam.me.uk>
binutils/
* testsuite/binutils-all/readelf.s-64-tmips: New test variant.
No one should be using versions of dejagnu without prune_warnings,
which was available in 1996 (dejagnu-1.3).
binutils/
* testsuite/lib/binutils-common.exp: Remove fallback prune_warnings.
gas/
* testsuite/lib/gas-defs.exp: Remove fallback prune_warnings.
PR 30699
* binutils/testsuite/binutils-all/objcopy.exp (keep_debug_symbols_for_elf_relocatable): Do not add sections containing the string "debug_" to the list of non-debug sections.
Make the n64 ABI the default for 64-bit Linux targets specified with
`-gnuabi64' suffix included in the target triplet, for configurations
such as the Debian mips64el and mips64r6el ports. Adjust testsuite
configuration accordingly.
There are the following regressions with the new target triplet:
mips64-linux-gnuabi64 +FAIL: readelf -S bintest
mips64-linux-gnuabi64 +FAIL: MIPS reloc estimation 1
mips64el-linux-gnuabi64 +FAIL: readelf -S bintest
mips64el-linux-gnuabi64 +FAIL: MIPS reloc estimation 1
The `readelf' issue comes from a difference in section headers produced
that the `binutils/testsuite/binutils-all/readelf.s-64' pattern template
does not match. While there has been a precedent it does not appear to
me that there is a clear advantage from adding more and more variations
to the template rather than forking the existing template into multiple
ones for a more exact match. So this is best deferred to a separate
discussion.
The MIPS reloc estimation issue is an actual bug in `objdump', which
discards a number of trailing entries from output here for n64 composed
relocations:
DYNAMIC RELOCATION RECORDS
OFFSET TYPE VALUE
0000000000000000 R_MIPS_NONE *ABS*
0000000000000000 R_MIPS_NONE *ABS*
and consequently `ld/testsuite/ld-mips-elf/reloc-estimate-1.d' does not
match even though ELF output produced is correct according to `readelf':
Relocation section '.rel.dyn' at offset 0x10400 contains 2 entries:
Offset Info Type Sym. Value Sym. Name
000000000000 000000000000 R_MIPS_NONE
Type2: R_MIPS_NONE
Type3: R_MIPS_NONE
000000010000 000300001203 R_MIPS_REL32 0000000000010010 foo@@V2
Type2: R_MIPS_64
Type3: R_MIPS_NONE
As a genuine bug this has to be handled separately.
Co-Authored by: Maciej W. Rozycki <macro@orcam.me.uk>
bfd/
* config.bfd: Add `mips64*el-*-linux*-gnuabi64' and
`mips64*-*-linux*-gnuabi64' targets.
binutils/
* testsuite/binutils-all/mips/mips.exp: Handle `*-*-*-gnuabi64'
targets.
* testsuite/binutils-all/objcopy.exp: Handle
`mips64*-*-*-gnuabi64' targets.
* testsuite/binutils-all/remove-relocs-01.d: Likewise.
* testsuite/binutils-all/remove-relocs-04.d: Likewise.
* testsuite/binutils-all/remove-relocs-05.d: Likewise.
* testsuite/binutils-all/remove-relocs-06.d: Likewise.
gas/
* configure.ac: Handle `mips64*-linux-gnuabi64' targets.
* configure: Regenerate.
* testsuite/gas/mips/compact-eh-eb-7.d: Handle
`mips64*-*-*-gnuabi64' targets.
* testsuite/gas/mips/compact-eh-el-7.d: Likewise.
ld/
* configure.tgt: Add `mips64*el-*-linux-gnuabi64' and
`mips64*-*-linux-gnuabi64' targets.
* testsuite/ld-undefined/undefined.exp: Handle
`mips64*-*-*-gnuabi64' targets.
* testsuite/ld-mips-elf/attr-gnu-4-10.d: Likewise.
* testsuite/ld-mips-elf/compact-eh6.d: Likewise.
* testsuite/ld-mips-elf/mips-elf.exp: Handle `*-*-*-gnuabi64'
targets.
