mirror of
https://github.com/espressif/ESP8266_RTOS_SDK.git
synced 2025-05-21 17:16:29 +08:00
392 lines
14 KiB
C
392 lines
14 KiB
C
// Copyright 2018-2025 Espressif Systems (Shanghai) PTE LTD
|
|
//
|
|
// Licensed under the Apache License, Version 2.0 (the "License");
|
|
// you may not use this file except in compliance with the License.
|
|
// You may obtain a copy of the License at
|
|
//
|
|
// http://www.apache.org/licenses/LICENSE-2.0
|
|
//
|
|
// Unless required by applicable law or agreed to in writing, software
|
|
// distributed under the License is distributed on an "AS IS" BASIS,
|
|
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
|
// See the License for the specific language governing permissions and
|
|
// limitations under the License.
|
|
|
|
#ifndef __GPIO_H__
|
|
#define __GPIO_H__
|
|
|
|
#include <stdint.h>
|
|
#include "esp_err.h"
|
|
|
|
#include "esp8266/eagle_soc.h"
|
|
#include "esp8266/pin_mux_register.h"
|
|
#include "esp8266/gpio_register.h"
|
|
|
|
#ifdef __cplusplus
|
|
extern "C" {
|
|
#endif
|
|
|
|
#ifndef BIT
|
|
#define BIT(x) (1 << (x))
|
|
#endif
|
|
|
|
#define GPIO_Pin_0 (BIT(0)) /* Pin 0 selected */
|
|
#define GPIO_Pin_1 (BIT(1)) /* Pin 1 selected */
|
|
#define GPIO_Pin_2 (BIT(2)) /* Pin 2 selected */
|
|
#define GPIO_Pin_3 (BIT(3)) /* Pin 3 selected */
|
|
#define GPIO_Pin_4 (BIT(4)) /* Pin 4 selected */
|
|
#define GPIO_Pin_5 (BIT(5)) /* Pin 5 selected */
|
|
#define GPIO_Pin_6 (BIT(6)) /* Pin 6 selected */
|
|
#define GPIO_Pin_7 (BIT(7)) /* Pin 7 selected */
|
|
#define GPIO_Pin_8 (BIT(8)) /* Pin 8 selected */
|
|
#define GPIO_Pin_9 (BIT(9)) /* Pin 9 selected */
|
|
#define GPIO_Pin_10 (BIT(10)) /* Pin 10 selected */
|
|
#define GPIO_Pin_11 (BIT(11)) /* Pin 11 selected */
|
|
#define GPIO_Pin_12 (BIT(12)) /* Pin 12 selected */
|
|
#define GPIO_Pin_13 (BIT(13)) /* Pin 13 selected */
|
|
#define GPIO_Pin_14 (BIT(14)) /* Pin 14 selected */
|
|
#define GPIO_Pin_15 (BIT(15)) /* Pin 15 selected */
|
|
#define GPIO_Pin_16 (BIT(16)) /* Pin 16 selected */
|
|
#define GPIO_Pin_All (0x1FFFF) /* All pins selected */
|
|
|
|
#define GPIO_MODE_DEF_DISABLE (0)
|
|
#define GPIO_MODE_DEF_INPUT (BIT(0))
|
|
#define GPIO_MODE_DEF_OUTPUT (BIT(1))
|
|
#define GPIO_MODE_DEF_OD (BIT(2))
|
|
|
|
#define GPIO_PIN_COUNT 17
|
|
|
|
#define GPIO_IS_VALID_GPIO(gpio_num) ((gpio_num < GPIO_PIN_COUNT)) /*!< Check whether it is a valid GPIO number */
|
|
#define RTC_GPIO_IS_VALID_GPIO(gpio_num) ((gpio_num == 16)) /*!< Check whether it is a valid RTC GPIO number */
|
|
|
|
typedef enum {
|
|
GPIO_NUM_0 = 0, /*!< GPIO0, input and output */
|
|
GPIO_NUM_1 = 1, /*!< GPIO1, input and output */
|
|
GPIO_NUM_2 = 2, /*!< GPIO2, input and output */
|
|
GPIO_NUM_3 = 3, /*!< GPIO3, input and output */
|
|
GPIO_NUM_4 = 4, /*!< GPIO4, input and output */
|
|
GPIO_NUM_5 = 5, /*!< GPIO5, input and output */
|
|
GPIO_NUM_6 = 6, /*!< GPIO6, input and output */
|
|
GPIO_NUM_7 = 7, /*!< GPIO7, input and output */
|
|
GPIO_NUM_8 = 8, /*!< GPIO8, input and output */
|
|
GPIO_NUM_9 = 9, /*!< GPIO9, input and output */
|
|
GPIO_NUM_10 = 10, /*!< GPIO10, input and output */
|
|
GPIO_NUM_11 = 11, /*!< GPIO11, input and output */
|
|
GPIO_NUM_12 = 12, /*!< GPIO12, input and output */
|
|
GPIO_NUM_13 = 13, /*!< GPIO13, input and output */
|
|
GPIO_NUM_14 = 14, /*!< GPIO14, input and output */
|
|
GPIO_NUM_15 = 15, /*!< GPIO15, input and output */
|
|
GPIO_NUM_16 = 16, /*!< GPIO15, input and output */
|
|
GPIO_NUM_MAX = 17,
|
|
/** @endcond */
|
|
} gpio_num_t;
|
|
|
|
typedef enum {
|
|
GPIO_INTR_DISABLE = 0, /*!< Disable GPIO interrupt */
|
|
GPIO_INTR_POSEDGE = 1, /*!< GPIO interrupt type : rising edge */
|
|
GPIO_INTR_NEGEDGE = 2, /*!< GPIO interrupt type : falling edge */
|
|
GPIO_INTR_ANYEDGE = 3, /*!< GPIO interrupt type : both rising and falling edge */
|
|
GPIO_INTR_LOW_LEVEL = 4, /*!< GPIO interrupt type : input low level trigger */
|
|
GPIO_INTR_HIGH_LEVEL = 5, /*!< GPIO interrupt type : input high level trigger */
|
|
GPIO_INTR_MAX,
|
|
} gpio_int_type_t;
|
|
|
|
typedef enum {
|
|
GPIO_MODE_DISABLE = GPIO_MODE_DEF_DISABLE, /*!< GPIO mode : disable input and output */
|
|
GPIO_MODE_INPUT = GPIO_MODE_DEF_INPUT, /*!< GPIO mode : input only */
|
|
GPIO_MODE_OUTPUT = GPIO_MODE_DEF_OUTPUT, /*!< GPIO mode : output only mode */
|
|
GPIO_MODE_OUTPUT_OD = ((GPIO_MODE_DEF_OUTPUT) | (GPIO_MODE_DEF_OD)), /*!< GPIO mode : output only with open-drain mode */
|
|
} gpio_mode_t;
|
|
|
|
typedef enum {
|
|
GPIO_PULLUP_ONLY, /*!< Pad pull up */
|
|
GPIO_PULLDOWN_ONLY, /*!< Pad pull down */
|
|
GPIO_FLOATING, /*!< Pad floating */
|
|
} gpio_pull_mode_t;
|
|
|
|
typedef enum {
|
|
GPIO_PULLUP_DISABLE = 0x0, /*!< Disable GPIO pull-up resistor */
|
|
GPIO_PULLUP_ENABLE = 0x1, /*!< Enable GPIO pull-up resistor */
|
|
} gpio_pullup_t;
|
|
|
|
typedef enum {
|
|
GPIO_PULLDOWN_DISABLE = 0x0, /*!< Disable GPIO pull-down resistor */
|
|
GPIO_PULLDOWN_ENABLE = 0x1, /*!< Enable GPIO pull-down resistor */
|
|
} gpio_pulldown_t;
|
|
|
|
/**
|
|
* @brief Configuration parameters of GPIO pad for gpio_config function
|
|
*/
|
|
typedef struct {
|
|
uint32_t pin_bit_mask; /*!< GPIO pin: set with bit mask, each bit maps to a GPIO */
|
|
gpio_mode_t mode; /*!< GPIO mode: set input/output mode */
|
|
gpio_pullup_t pull_up_en; /*!< GPIO pull-up */
|
|
gpio_pulldown_t pull_down_en; /*!< GPIO pull-down */
|
|
gpio_int_type_t intr_type; /*!< GPIO interrupt type */
|
|
} gpio_config_t;
|
|
|
|
typedef void (*gpio_isr_t)(void *);
|
|
typedef void *gpio_isr_handle_t;
|
|
|
|
/**
|
|
* @brief GPIO common configuration
|
|
*
|
|
* Configure GPIO's Mode,pull-up,PullDown,IntrType
|
|
*
|
|
* @param gpio_config Pointer to GPIO configure struct
|
|
*
|
|
* @return
|
|
* - ESP_OK success
|
|
* - ESP_ERR_INVALID_ARG Parameter error
|
|
*/
|
|
esp_err_t gpio_config(const gpio_config_t *gpio_cfg);
|
|
|
|
/**
|
|
* @brief GPIO set interrupt trigger type
|
|
*
|
|
* @param gpio_num GPIO number. If you want to set the trigger type of e.g. of GPIO12, gpio_num should be GPIO_NUM_12 (12);
|
|
* @param intr_type Interrupt type, select from gpio_int_type_t
|
|
*
|
|
* @return
|
|
* - ESP_OK Success
|
|
* - ESP_ERR_INVALID_ARG Parameter error
|
|
*/
|
|
esp_err_t gpio_set_intr_type(gpio_num_t gpio_num, gpio_int_type_t intr_type);
|
|
|
|
/**
|
|
* @brief Enable GPIO module interrupt signal
|
|
*
|
|
* @param gpio_num GPIO number. If you want to enable an interrupt on e.g. GPIO12, gpio_num should be GPIO_NUM_12 (12);
|
|
*
|
|
* @return
|
|
* - ESP_OK Success
|
|
* - ESP_ERR_INVALID_ARG Parameter error
|
|
*/
|
|
esp_err_t gpio_intr_enable(gpio_num_t gpio_num);
|
|
|
|
/**
|
|
* @brief Disable GPIO module interrupt signal
|
|
*
|
|
* @param gpio_num GPIO number. If you want to disable the interrupt of e.g. GPIO12, gpio_num should be GPIO_NUM_12 (12);
|
|
*
|
|
* @return
|
|
* - ESP_OK success
|
|
* - ESP_ERR_INVALID_ARG Parameter error
|
|
*/
|
|
esp_err_t gpio_intr_disable(gpio_num_t gpio_num);
|
|
|
|
/**
|
|
* @brief GPIO set output level
|
|
*
|
|
* @param gpio_num GPIO number. If you want to set the output level of e.g. GPIO16, gpio_num should be GPIO_NUM_16 (16);
|
|
* @param level Output level. 0: low ; 1: high
|
|
*
|
|
* @return
|
|
* - ESP_OK Success
|
|
* - ESP_ERR_INVALID_ARG GPIO number error
|
|
*/
|
|
esp_err_t gpio_set_level(gpio_num_t gpio_num, uint32_t level);
|
|
|
|
/**
|
|
* @brief GPIO get input level
|
|
*
|
|
* @note If the pad is not configured for input (or input and output) the returned value is always 0.
|
|
*
|
|
* @param gpio_num GPIO number. If you want to get the logic level of e.g. pin GPIO16, gpio_num should be GPIO_NUM_16 (16);
|
|
*
|
|
* @return
|
|
* - 0 the GPIO input level is 0
|
|
* - 1 the GPIO input level is 1
|
|
*/
|
|
int gpio_get_level(gpio_num_t gpio_num);
|
|
|
|
/**
|
|
* @brief GPIO set direction
|
|
*
|
|
* Configure GPIO direction,such as output_only,input_only
|
|
*
|
|
* @param gpio_num Configure GPIO pins number, it should be GPIO number. If you want to set direction of e.g. GPIO16, gpio_num should be GPIO_NUM_16 (16);
|
|
* @param mode GPIO direction
|
|
*
|
|
* @return
|
|
* - ESP_OK Success
|
|
* - ESP_ERR_INVALID_ARG GPIO error
|
|
*/
|
|
esp_err_t gpio_set_direction(gpio_num_t gpio_num, gpio_mode_t mode);
|
|
|
|
/**
|
|
* @brief Configure GPIO pull-up/pull-down resistors
|
|
*
|
|
* @param gpio_num GPIO number. If you want to set pull up or down mode for e.g. GPIO16, gpio_num should be GPIO_NUM_16 (16);
|
|
* @param pull GPIO pull up/down mode.
|
|
*
|
|
* @note The GPIO of esp8266 can not be pulled down except RTC GPIO which can not be pulled up.
|
|
*
|
|
* @return
|
|
* - ESP_OK Success
|
|
* - ESP_ERR_INVALID_ARG : Parameter error
|
|
*/
|
|
esp_err_t gpio_set_pull_mode(gpio_num_t gpio_num, gpio_pull_mode_t pull);
|
|
|
|
/**
|
|
* @brief Enable GPIO wake-up function.
|
|
*
|
|
* @note RTC IO can not use the wakeup function
|
|
*
|
|
* @param gpio_num GPIO number.
|
|
*
|
|
* @param intr_type GPIO wake-up type. Only GPIO_INTR_LOW_LEVEL or GPIO_INTR_HIGH_LEVEL can be used.
|
|
*
|
|
* @return
|
|
* - ESP_OK Success
|
|
* - ESP_ERR_INVALID_ARG Parameter error
|
|
*/
|
|
esp_err_t gpio_wakeup_enable(gpio_num_t gpio_num, gpio_int_type_t intr_type);
|
|
|
|
/**
|
|
* @brief Disable GPIO wake-up function.
|
|
*
|
|
* @note RTC IO can not use the wakeup function
|
|
*
|
|
* @param gpio_num GPIO number
|
|
*
|
|
* @return
|
|
* - ESP_OK Success
|
|
* - ESP_ERR_INVALID_ARG Parameter error
|
|
*/
|
|
esp_err_t gpio_wakeup_disable(gpio_num_t gpio_num);
|
|
|
|
/**
|
|
* @brief Register GPIO interrupt handler, the handler is an ISR.
|
|
*
|
|
* This ISR function is called whenever any GPIO interrupt occurs. See
|
|
* the alternative gpio_install_isr_service() and
|
|
* gpio_isr_handler_add() API in order to have the driver support
|
|
* per-GPIO ISRs.
|
|
*
|
|
* @param fn Interrupt handler function.
|
|
* @param no_use In order to be compatible with esp32, the parameter has no practical meaning and can be filled with 0.
|
|
* @param arg Parameter for handler function
|
|
* @param handle Pointer to return handle. In order to be compatible with esp32,the parameter has no practical meaning and can be filled with NULL.
|
|
*
|
|
* @return
|
|
* - ESP_OK Success ;
|
|
* - ESP_ERR_INVALID_ARG GPIO error
|
|
* - ESP_ERR_NOT_FOUND No free interrupt found with the specified flags
|
|
*/
|
|
esp_err_t gpio_isr_register(void (*fn)(void *), void *arg, int no_use, gpio_isr_handle_t *handle);
|
|
|
|
/**
|
|
* @brief Enable pull-up on GPIO.
|
|
*
|
|
* @param gpio_num GPIO number
|
|
*
|
|
* @note The GPIO of esp8266 can not be pulled down except RTC GPIO which can not be pulled up.
|
|
*
|
|
* @return
|
|
* - ESP_OK Success
|
|
* - ESP_ERR_INVALID_ARG Parameter error
|
|
*/
|
|
esp_err_t gpio_pullup_en(gpio_num_t gpio_num);
|
|
|
|
/**
|
|
* @brief Disable pull-up on GPIO.
|
|
*
|
|
* @param gpio_num GPIO number
|
|
*
|
|
* @note The GPIO of esp8266 can not be pulled down except RTC GPIO which can not be pulled up.
|
|
*
|
|
* @return
|
|
* - ESP_OK Success
|
|
* - ESP_ERR_INVALID_ARG Parameter error
|
|
*/
|
|
esp_err_t gpio_pullup_dis(gpio_num_t gpio_num);
|
|
|
|
/**
|
|
* @brief Enable pull-down on GPIO.
|
|
*
|
|
* @param gpio_num GPIO number
|
|
*
|
|
* @note The GPIO of esp8266 can not be pulled down except RTC GPIO which can not be pulled up.
|
|
*
|
|
* @return
|
|
* - ESP_OK Success
|
|
* - ESP_ERR_INVALID_ARG Parameter error
|
|
*/
|
|
esp_err_t gpio_pulldown_en(gpio_num_t gpio_num);
|
|
|
|
/**
|
|
* @brief Disable pull-down on GPIO.
|
|
*
|
|
* @param gpio_num GPIO number
|
|
*
|
|
* @note The GPIO of esp8266 can not be pulled down except RTC GPIO which can not be pulled up.
|
|
*
|
|
* @return
|
|
* - ESP_OK Success
|
|
* - ESP_ERR_INVALID_ARG Parameter error
|
|
*/
|
|
esp_err_t gpio_pulldown_dis(gpio_num_t gpio_num);
|
|
|
|
/**
|
|
* @brief Install the driver's GPIO ISR handler service, which allows per-pin GPIO interrupt handlers.
|
|
*
|
|
* This function is incompatible with gpio_isr_register() - if that function is used, a single global ISR is registered for all GPIO interrupts. If this function is used, the ISR service provides a global GPIO ISR and individual pin handlers are registered via the gpio_isr_handler_add() function.
|
|
*
|
|
* @param no_use In order to be compatible with esp32, the parameter has no practical meaning and can be filled with 0.
|
|
*
|
|
* @return
|
|
* - ESP_OK Success
|
|
* - ESP_ERR_NO_MEM No memory to install this service
|
|
* - ESP_ERR_INVALID_STATE ISR service already installed.
|
|
* - ESP_ERR_NOT_FOUND No free interrupt found with the specified flags
|
|
* - ESP_ERR_INVALID_ARG GPIO error
|
|
*/
|
|
esp_err_t gpio_install_isr_service(int no_use);
|
|
|
|
/**
|
|
* @brief Uninstall the driver's GPIO ISR service, freeing related resources.
|
|
*/
|
|
void gpio_uninstall_isr_service();
|
|
|
|
/**
|
|
* @brief Add ISR handler for the corresponding GPIO pin.
|
|
*
|
|
* Call this function after using gpio_install_isr_service() to
|
|
* install the driver's GPIO ISR handler service.
|
|
*
|
|
* This ISR handler will be called from an ISR. So there is a stack
|
|
* size limit (configurable as "ISR stack size" in menuconfig). This
|
|
* limit is smaller compared to a global GPIO interrupt handler due
|
|
* to the additional level of indirection.
|
|
*
|
|
* @param gpio_num GPIO number
|
|
* @param isr_handler ISR handler function for the corresponding GPIO number.
|
|
* @param args parameter for ISR handler.
|
|
*
|
|
* @return
|
|
* - ESP_OK Success
|
|
* - ESP_ERR_INVALID_STATE Wrong state, the ISR service has not been initialized.
|
|
* - ESP_ERR_INVALID_ARG Parameter error
|
|
*/
|
|
esp_err_t gpio_isr_handler_add(gpio_num_t gpio_num, gpio_isr_t isr_handler, void *args);
|
|
|
|
/**
|
|
* @brief Remove ISR handler for the corresponding GPIO pin.
|
|
*
|
|
* @param gpio_num GPIO number
|
|
*
|
|
* @return
|
|
* - ESP_OK Success
|
|
* - ESP_ERR_INVALID_STATE Wrong state, the ISR service has not been initialized.
|
|
* - ESP_ERR_INVALID_ARG Parameter error
|
|
*/
|
|
esp_err_t gpio_isr_handler_remove(gpio_num_t gpio_num);
|
|
|
|
|
|
|
|
#ifdef __cplusplus
|
|
}
|
|
#endif
|
|
|
|
#endif /* _DRIVER_GPIO_H_ */ |