/**
* spi_interface.h
*
* Defines and Macros for the SPI.
*
* Copyright @ 2015 Espressif System Co., Ltd.
* All Rights Reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are NOT permitted except as agreed by
* Espressif System Co., Ltd.
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS,
* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
*/
/**
* @file spi_interface.h
* @brief Defines and Macros for the SPI.
*/
#ifndef __SPI_INTERFACE_H__
#define __SPI_INTERFACE_H__
#include "spi_register.h"
#include "c_types.h"
//*****************************************************************************
//
// Make sure all of the definitions in this header have a C binding.
//
//*****************************************************************************
#ifdef __cplusplus
extern "C"
{
#endif
/**
* @brief Defines slave commands. Default value based on slave ESP8266.
*/
#define MASTER_WRITE_DATA_TO_SLAVE_CMD 2
#define MASTER_READ_DATA_FROM_SLAVE_CMD 3
#define MASTER_WRITE_STATUS_TO_SLAVE_CMD 1
#define MASTER_READ_STATUS_FROM_SLAVE_CMD 4
/**
* @brief Support HSPI and SPI module.
*
*/
typedef enum
{
SpiNum_SPI = 0,
SpiNum_HSPI = 1,
} SpiNum;
/**
* @brief The SPI module can work in either master or slave mode.
*
*/
typedef enum
{
SpiMode_Master = 0,
SpiMode_Slave = 1,
} SpiMode;
/**
* @brief SPI sub mode
*
* Support 4 sub modes based on SPI clock polarity and phase.
* SPI_CPOL SPI_CPHA SubMode
* 0 0 0
* 0 1 1
* 1 0 2
* 1 1 3
*/
typedef enum
{
SpiSubMode_0 = 0,
SpiSubMode_1 = 1,
SpiSubMode_2 = 2,
SpiSubMode_3 = 3,
} SpiSubMode;
/**
* @brief The SPI module working speed.
*
* @attention Max speed 80MHz
*
*/
typedef enum
{
SpiSpeed_2MHz = 40 - 1,
SpiSpeed_5MHz = 16 - 1,
SpiSpeed_10MHz = 8 - 1,
SpiSpeed_16MHz = 5 - 1,
SpiSpeed_20MHz = 4 - 1,
} SpiSpeed;
/**
* @brief The SPI mode working speed.
*
*/
typedef enum
{
SpiBitOrder_MSBFirst = 0,
SpiBitOrder_LSBFirst = 1,
} SpiBitOrder;
// @brief SPI interrupt soource defined.
typedef enum
{
SpiIntSrc_TransDoneEn = SPI_TRANS_DONE_EN,
SpiIntSrc_WrStaDoneEn = SPI_SLV_WR_STA_DONE_EN,
SpiIntSrc_RdStaDoneEn = SPI_SLV_RD_STA_DONE_EN,
SpiIntSrc_WrBufDoneEn = SPI_SLV_WR_BUF_DONE_EN,
SpiIntSrc_RdBufDoneEn = SPI_SLV_RD_BUF_DONE_EN,
} SpiIntSrc;
// @brief SPI CS pin.
typedef enum
{
SpiPinCS_0 = 0,
SpiPinCS_1 = 1,
SpiPinCS_2 = 2,
} SpiPinCS;
#pragma pack (1)
/**
* @brief SPI attribute
*/
typedef struct
{
SpiMode mode; ///< Master or slave mode
SpiSubMode subMode; ///< SPI SPI_CPOL SPI_CPHA mode
SpiSpeed speed; ///< SPI Clock
SpiBitOrder bitOrder; ///< SPI bit order
} SpiAttr;
/**
* @brief SPI attribute
*/
typedef struct
{
uint16_t cmd; ///< Command value
uint8_t cmdLen; ///< Command byte length
uint32_t *addr; ///< Point to address value
uint8_t addrLen; ///< Address byte length
uint32_t *data; ///< Point to data buffer
uint8_t dataLen; ///< Data byte length.
} SpiData;
#pragma upack (1)
#define SHOWREG() __ShowRegValue(__func__, __LINE__);
/**
* @brief Print debug information.
*
*/
void __ShowRegValue(const char * func, uint32_t line);
/**
* @brief Initialize SPI module.
*
* @param [in] spiNum
* Indicates which submode to be used, SPI or HSPI.
* @param [in] pAttr
* Pointer to a struct SpiAttr that indicates SPI working attribution.
*
* @return void.
*/
void SPIInit(SpiNum spiNum, SpiAttr* pAttr);
/**
* @brief Set slave address value by master.
*
* @param [in] spiNum
* Indicates which submode to be used, SPI or HSPI.
* @param [in] addr
* Slave address to be set.
*
* @return void.
*/
void SPIMasterCfgAddr(SpiNum spiNum, uint32_t addr);
/**
* @brief Set command value by master.
*
* @param [in] spiNum
* Indicates which submode to be used, SPI or HSPI.
* @param [in] cmd
* Command will be send to slave.
*
* @return void.
*/
void SPIMasterCfgCmd(SpiNum spiNum, uint32_t cmd);
/**
* @brief Send data to slave from master.
*
* @param [in] spiNum
* Indicates which submode to be used, SPI or HSPI.
* @param [in] pInData
* Pointer to a strcuture that will be send.
*
* @return int, -1:indicates failure,others indicates success.
*/
int SPIMasterSendData(SpiNum spiNum, SpiData* pInData);
/**
* @brief Receive data from slave by master.
*
* @param [in] spiNum
* Indicates which submode to be used, SPI or HSPI.
* @param [in] pOutData
* Point to data buffer.
*
* @return int, -1:indicates failure,others indicates success.
*
*/
int SPIMasterRecvData(SpiNum spiNum, SpiData* pOutData);
/**
* @brief Load data to slave send buffer.
*
* @param [in] spiNum
* Indicates which submode to be used, SPI or HSPI.
* @param [in] pInData
* Point to data buffer.
* @param [in] outLen
* The number of bytes to be set.
*
* @return int, -1:indicates failure,others indicates success.
*/
int SPISlaveSendData(SpiNum spiNum, uint32_t *pInData, uint8_t outLen);
/**
* @brief Receive data by slave.
*
* @param [in] spiNum
* Indicates which submode to be used, SPI or HSPI.
* @param [in] isrFunc
* isrFunc is a pointer to the function to be called when the SPI interrupt occurs.
*
* @return int, -1:indicates failure,others indicates success.
*/
int SPISlaveRecvData(SpiNum spiNum, void(*isrFunc)(void*));
/**
* @brief Set slave status by master.
*
* @param [in] spiNum
* Indicates which submode to be used, SPI or HSPI.
* @param [in] data
* Data will be write to slave SPI_WR_STATUS.
*
* @return void.
*
* @attention Just for ESP8266(slave) register of RD_STATUS or WR_STATUS.
*/
void SPIMasterSendStatus(SpiNum spiNum, uint8_t data);
/**
* @brief Get salve status by master.
*
* @param [in] spiNum
* Indicates which submode to be used, SPI or HSPI.
*
* @return int, -1: indicates failure; other value in slave status.
*
* @attention Just for ESP8266(slave) register of RD_STATUS or WR_STATUS.
*/
int SPIMasterRecvStatus(SpiNum spiNum);
/**
* @brief Select SPI CS pin.
*
* @param [in] spiNum
* Indicates which submode to be used, SPI or HSPI.
* @param [in] pinCs
* Indicates which SPI pin to choose.
*
* @return void.
*/
void SPICsPinSelect(SpiNum spiNum, SpiPinCS pinCs);
/**
* @brief Enable SPI module interrupt source.
*
* @param [in] spiNum
* Indicates which submode to be used, SPI or HSPI.
* @param [in] intSrc
* Indicates which interrupt source to enable.
*
* @return void.
*/
void SPIIntEnable(SpiNum spiNum, SpiIntSrc intSrc);
/**
* @brief Disable SPI module interrupt source.
*
* @param [in] spiNum
* Indicates which submode to be used, SPI or HSPI.
* @param [in] intSrc
* Indicates which interrupt source to disable.
*
* @return void.
*/
void SPIIntDisable(SpiNum spiNum, SpiIntSrc intSrc);
/**
* @brief Clear all of spi interrupt.
*
* @param [in] spiNum
* Indicates which submode to be used, SPI or HSPI.
*
* @return void.
*/
void SPIIntClear(SpiNum spiNum);
#ifdef __cplusplus
}
#endif
#endif // __SPI_INTERFACE_H__