diff --git a/components/esp8266/Kconfig b/components/esp8266/Kconfig
index 9b1f08cb..1bb95ae1 100644
--- a/components/esp8266/Kconfig
+++ b/components/esp8266/Kconfig
@@ -560,39 +560,17 @@ endmenu
 
 menu PHY
 
-choice ESP8266_PHY_CALIBRATION
-    prompt "RF calibration"
-    default ESP8266_PHY_FULL_CALIBRATION
-    help
-        If calibration data is not found, full calibration will be performed. To ensure better RF performance,
-        it is recommend to set RF_calibration to ESP8266_PHY_FULL_CALIBRATION, otherwise the RF performance may become poor.
-
-        Full calibration needs 170 - 180ms.
-        Partial calibration needs 35 - 40ms.
-        No calibration needs 3.260 - 3.264ms.
-
-config ESP8266_PHY_FULL_CALIBRATION
-    bool "RF full calibration"
-config ESP8266_PHY_NO_CALIBRATION
-    bool "RF no calibration"
-config ESP8266_PHY_PARTIAL_CALIBRATION
-    bool "RF partial calibration"
-endchoice
-
-config ESP8266_PHY_CALIBRATION
-    int
-    default 3 if ESP8266_PHY_FULL_CALIBRATION
-    default 2 if ESP8266_PHY_PARTIAL_CALIBRATION
-    default 1 if ESP8266_PHY_NO_CALIBRATION
-
 config ESP_PHY_CALIBRATION_AND_DATA_STORAGE
     bool "Store phy calibration data in NVS"
     default y
     help
         If this option is enabled, NVS will be initialized and calibration data will be loaded from there.
-        PHY calibration will be skipped on deep sleep wakeup. If calibration data is not found, full calibration
-        will be performed and stored in NVS. Normally, only partial calibration will be performed. 
-        If this option is disabled, full calibration will be performed.
+        If calibration data is not found, full calibration will be performed and stored in NVS. Normally,
+        only partial calibration will be performed. If this option is disabled, full calibration will be performed.
+
+        Full calibration needs 170 - 180ms.
+        Partial calibration needs 35 - 40ms.
+        No calibration needs 3.260 - 3.264ms.
 
         If it's easy that your board calibrate bad data, choose 'n'.
         Two cases for example, you should choose 'n':
diff --git a/components/esp8266/source/phy_init.c b/components/esp8266/source/phy_init.c
index cc1f01ac..9368bae6 100644
--- a/components/esp8266/source/phy_init.c
+++ b/components/esp8266/source/phy_init.c
@@ -79,10 +79,12 @@ esp_err_t esp_phy_rf_init(const esp_phy_init_data_t* init_data, esp_phy_calibrat
                              phy_check_data_table(phy_rx_gain_dc_table, 125, 1);
 
     phy_afterwake_set_rfoption(1);
-    phy_set_powerup_option(CONFIG_ESP8266_PHY_CALIBRATION);
 
     if (!cal_data_check) {
+        phy_set_powerup_option(1);
         write_data_to_rtc(calibration_data->rf_cal_data);
+    } else {
+        phy_set_powerup_option(3);
     }
 
     esp_efuse_mac_get_default(sta_mac);